### Start the UE Example

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/nbiot/source/index.html

Runs the UE to decode the test transmission by specifying the RNTI and skipping SIB2 decoding.

```bash
$ ./lib/examples/npdsch_ue -f 868e6 -r 0x1234 -s
Opening RF device...
Found Rafael Micro R820T tuner
Soapy has found device #0: driver=rtlsdr, label=Generic RTL2832U OEM :: 00000001, manufacturer=Realtek, product=RTL2838UHIDIR, serial=00000001, tuner=Rafael Micro R820T,
Selecting Soapy device: 0
[INFO] Opening Generic RTL2832U OEM :: 00000001...
Found Rafael Micro R820T tuner
Setting up Rx stream with 1 channel(s)
[INFO] Using format CF32.
[R82XX] PLL not locked!
Available device sensors:
Available sensors for Rx channel 0:
State of gain elements for Rx channel 0 (AGC supported):
 - TUNER: 0.00 dB
State of gain elements for Tx channel 0 (AGC supported):
 - TUNER: 0.00 dB
Rx antenna set to RX
Tx antenna set to RX
Set RX gain: 40.0 dB
Set RX freq: 868.000000 MHz
Setting sampling rate 1.92 MHz
NSSS with peak=24.363365, cell-id: 0, partial SFN: 0
*Found n_id_ncell:   0 DetectRatio= 0% PSR=8.66, Power=86.4 dBm
MIB received (CFO:  -1,55 kHz) FrameCnt: 0, State: 10
SIB1 received
CFO:  -1,41 kHz, RSRP: 12,0 dBm SNR: 19,0 dB, RSRQ: -3,7 dB, NPDCCH detected: 510, NPDSCH-BLER:  0,20% (1 of total 511), NPDSCH-Rate: 10,36 kbit/s
```

--------------------------------

### Example Console Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_nsa_amari/source/index.rst.txt

Expected console output after starting the base station.

```text
LTE Base Station version 2021-03-15, Copyright (C) 2012-2021 Amarisoft
This software is licensed to Software Radio Systems (SRS).
Support and software update available until 2021-10-29.
RF0: sample_rate=11.520 MHz dl_freq=2140.000 MHz ul_freq=1950.000 MHz (band 1) dl_ant=1 ul_ant=1
RF1: sample_rate=23.040 MHz dl_freq=3507.840 MHz ul_freq=3507.840 MHz (band n78) dl_ant=1 ul_ant=1
```

--------------------------------

### Install LimeSuite

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/pi4/source/index.rst.txt

Build and install LimeSuite, then verify the connection with LimeUtil and SoapySDRUtil.

```bash
sudo apt install libusb-1.0-0-dev
git clone https://github.com/myriadrf/LimeSuite.git
cd LimeSuite
git checkout tags/v20.01.0
mkdir builddir && cd builddir
cmake ../
make -j4
sudo make install
sudo ldconfig
cd ..
cd udev-rules
sudo ./install.sh

## Then test the connection by typing:
LimeUtil --find
LimeUtil --update
SoapySDRUtil --find
```

--------------------------------

### Install ZeroMQ via APT

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/zeromq/source/index.rst.txt

Install the ZeroMQ development libraries on Ubuntu systems.

```bash
sudo apt-get install libzmq3-dev
```

--------------------------------

### Install srsUE on Ubuntu

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/2_ue_getstarted.rst.txt

Commands to add the repository and install srsUE using apt.

```bash
sudo add-apt-repository ppa:srslte/releases
sudo apt-get update
sudo apt-get install srsue
```

--------------------------------

### Install SoapySDR

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/pi4/source/index.rst.txt

Build and install SoapySDR from source.

```bash
git clone https://github.com/pothosware/SoapySDR.git
cd SoapySDR
git checkout tags/soapy-sdr-0.7.2
mkdir build && cd build
cmake ..
make -j4
sudo make install
sudo ldconfig
```

--------------------------------

### Start UE

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/5g_nsa_zmq/source/index.html

Launch the UE service to connect to the eNB/gNB.

```bash
sudo srsue
```

```text
Opening 2 channels in RF device=zmq with args=tx_port0=tcp://*:2001,rx_port0=tcp://localhost:2000,tx_port1=tcp://*:2101,rx_port1=tcp://localhost:2100,id=ue,base_srate=23.04e6
CHx base_srate=23.04e6
CHx id=ue
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
CH0 rx_port=tcp://localhost:2000
CH0 tx_port=tcp://*:2001
CH1 rx_port=tcp://localhost:2100
CH1 tx_port=tcp://*:2101
Waiting PHY to initialize ... done!

Attaching UE...
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
.
Found Cell:  Mode=FDD, PCI=1, PRB=50, Ports=1, CP=Normal, CFO=-0.2 KHz
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Found PLMN:  Id=00101, TAC=7
Random Access Transmission: seq=33, tti=981, ra-rnti=0x2
RRC Connected
Random Access Complete.     c-rnti=0x46, ta=0
Network attach successful. IP: 172.16.0.3
Software Radio Systems RAN (srsRAN) 13/10/2021 15:29:9 TZ:0
RRC NR reconfiguration successful.
Random Access Transmission: prach_occasion=0, preamble_index=0, ra-rnti=0xf, tti=1611
Random Access Complete.     c-rnti=0x4601, ta=0
```

--------------------------------

### Launch Pi4 eNodeB

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/pi4/source/index.html

Starts the srsENB software using the specified configuration file. The first execution may take several minutes for initial setup.

```bash
sudo srsenb /root/.config/srsran_4g/enb.conf
```

--------------------------------

### Build libzmq from Source

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/zeromq/source/index.rst.txt

Manual compilation and installation steps for libzmq.

```bash
git clone https://github.com/zeromq/libzmq.git
cd libzmq
./autogen.sh
./configure
make
sudo make install
sudo ldconfig
```

--------------------------------

### Install LimeSuite

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/pi4/source/index.html

Build and install LimeSuite for LimeSDR support, including udev rules.

```bash
sudo apt install libusb-1.0-0-dev
git clone https://github.com/myriadrf/LimeSuite.git
cd LimeSuite
git checkout tags/v20.01.0
mkdir builddir && cd builddir
cmake ../
make -j4
sudo make install
sudo ldconfig
cd ..
cd udev-rules
sudo ./install.sh

## Then test the connection by typing:
LimeUtil --find
LimeUtil --update
SoapySDRUtil --find

```

--------------------------------

### Install configuration files

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/cots_ue/source/index.rst.txt

Run this command to install base configuration files for srsRAN 4G.

```bash
sudo srsran_4g_install_configs.sh <user/service>
```

--------------------------------

### Build czmq from Source

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/zeromq/source/index.rst.txt

Manual compilation and installation steps for czmq.

```bash
git clone https://github.com/zeromq/czmq.git
cd czmq
./autogen.sh
./configure
make
sudo make install
sudo ldconfig
```

--------------------------------

### gNB Initialization Output

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/5g_sa_amari/source/index.html

Example console output upon gNB startup.

```text
      Base Station version 2021-03-15, Copyright (C) 2012-2021 Amarisoft

RF0: sample_rate=61.440 MHz dl_freq=1836.740 MHz ul_freq=1741.740 MHz (band n3) dl_ant=1 ul_ant=1
```

--------------------------------

### Install srsENB on Ubuntu

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsenb/source/2_enb_getstarted.rst.txt

Commands to add the repository and install srsENB binary packages.

```bash
sudo add-apt-repository ppa:srslte/releases
sudo apt-get update
sudo apt-get install srsenb
```

--------------------------------

### Example srsENB Console Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsenb/source/2_enb_getstarted.rst.txt

Sample output showing successful initialization of the eNodeB.

```text
linux; GNU C++ version 6.3.0 20170618; Boost_106200; UHD_003.009.007-release
Built in RelWithDebInfo mode using commit 6b2961fce on branch next.

---  Software Radio Systems LTE eNodeB  ---

Reading configuration file /conf/enb.conf...
Setting number of control symbols to 3 for 25 PRB cell.
Opening USRP with args: type=b200,master_clock_rate=30.72e6
Setting frequency: DL=2630.0 Mhz, UL=2510.0 MHz
Setting Sampling frequency 5.76 MHz
Enter t to stop trace.

==== eNodeB started ===
```

--------------------------------

### Install UHD Drivers

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/pi4/source/index.rst.txt

Install UHD development libraries and host tools for USRP devices, then verify the connection.

```bash
sudo apt install libuhd-dev libuhd3.15.0 uhd-host
sudo /usr/lib/uhd/utils/uhd_images_downloader.py

## Then test the connection by typing:
sudo uhd_usrp_probe
```

--------------------------------

### Console Output Examples

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_sa_amari/source/index.rst.txt

Expected console output during network initialization and operation.

```text
Base Station version 2021-03-15, Copyright (C) 2012-2021 Amarisoft

  RF0: sample_rate=61.440 MHz dl_freq=1836.740 MHz ul_freq=1741.740 MHz (band n3) dl_ant=1 ul_ant=1
```

```text
Opening 1 channels in RF device=uhd with args=type=x300,serial=30B8658,clock=external,sampling_rate=23.04e6,lo_freq_offset_hz=23.04e6,None
```

```text
Found Cell:  Mode=FDD, PCI=1, PRB=50, Ports=1, CFO=0.1 KHz
  Found PLMN:  Id=00101, TAC=7
  Random Access Transmission: prach_occasion=0, preamble_index=0, ra-rnti=0xf, tti=3851
  Random Access Complete.     c-rnti=0x4601, ta=3
  RRC Connected
  RRC NR reconfiguration successful.
  PDU Session Establishment successful. IP: 192.168.4.2
  RRC NR reconfiguration successful.
```

```text
PRACH: cell=01 seq=0 ta=3 snr=29.1 dB
```

```text
---------Signal-----------|-----------------DL-----------------|-----------
  rat  pci  rsrp   pl   cfo | mcs  snr  iter  brate  bler  ta_us | mcs   buff  brate  bler
   nr  500    -3    0   2.0 |  27   28   2.0    23M    0%    0.0 |  27     59    16M    0%
   nr  500    -3    0   1.6 |  27   28   2.1    23M    0%    0.0 |  27    30k    16M    0%
   nr  500    -3    0   2.0 |  27   28   2.1    23M    0%    0.0 |  27    44k    16M    0%
   nr  500    -3    0  824m |  27   28   2.1    23M    0%    0.0 |  27    26k    16M    0%
   nr  500    -3    0   1.1 |  27   28   2.1    23M    0%    0.0 |  27    10k    17M    0%
   nr  500    -3    0   1.3 |  27   28   2.0    23M    0%    0.0 |  27    0.0    16M    0%
   nr  500    -3    0  106m |  27   28   2.0    23M    0%    0.0 |  27   118k    16M    0%
   nr  500    -4    0   1.0 |  27   28   2.1    22M    0%    0.0 |  27    52k    21M    0%
   nr  500    -4    0   1.9 |  27   28   2.0    22M    0%    0.0 |  27    57k    21M    0%
   nr  500    -3    0  840m |  27   28   2.0    23M    0%    0.0 |  27    54k    19M    0%
   nr  500    -3    0  160m |  27   28   2.0    23M    0%    0.0 |  27    20k    18M    0%
```

--------------------------------

### Example Log Output with Hex

Source: https://docs.srsran.com/projects/4g/en/latest/usermanuals/source/srsue/source/2_ue_getstarted.html

Log output example including hex message data.

```text
17:52:25.246 [RLC ]  Info    DRB1 Tx SDU
         0000: 8b 45 00 00 c7 f3 8b 40 00 01 11 d1 f6 c0 a8 03
         0010: 01 ef ff ff fa 92 55 07 6c 00 b3 ee 41 4d 2d 53
```

--------------------------------

### Start EPC

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_nsa_zmq/source/index.rst.txt

Command to launch the EPC and expected initialization output.

```bash
sudo srsepc
```

```text
HSS Initialized.
MME S11 Initialized
MME GTP-C Initialized
MME Initialized. MCC: 0xf001, MNC: 0xff01
SPGW GTP-U Initialized.
SPGW S11 Initialized.
SP-GW Initialized.
```

--------------------------------

### Run EPC

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/zeromq/source/index.rst.txt

Start the Evolved Packet Core component.

```bash
sudo ./srsepc/src/srsepc
```

--------------------------------

### Start srsEPC

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_nsa_cots/source/index.rst.txt

Launch the srsEPC service to initialize the HSS, MME, and SPGW components.

```bash
sudo srsepc
```

```text
Built in Release mode using commit c892ae56b on branch master.

---  Software Radio Systems EPC  ---

Reading configuration file /etc/srsran_4G/epc.conf...
HSS Initialized.
MME S11 Initialized
MME GTP-C Initialized
MME Initialized. MCC: 0xf901, MNC: 0xff70
SPGW GTP-U Initialized.
SPGW S11 Initialized.
SP-GW Initialized.
```

--------------------------------

### Install and Configure srsRAN 4G

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/general/source/1_installation.rst.txt

Final steps to install the built binaries and copy default configuration files to the user directory.

```bash
sudo make install
srsran_install_configs.sh user
```

--------------------------------

### Start srsENB

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_nsa_cots/source/index.rst.txt

Launch the srsENB service to begin eNodeB operations.

```bash
sudo srsenb
```

```text
---  Software Radio Systems LTE eNodeB  ---
```

--------------------------------

### Install srsEPC on Ubuntu

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsepc/source/2_epc_getstarted.rst.txt

Use these commands to add the repository and install the srsEPC binary package on Ubuntu systems.

```bash
sudo add-apt-repository ppa:srslte/releases
sudo apt-get update
sudo apt-get install srsepc
```

--------------------------------

### iPerf Output Examples

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/5g_nsa_zmq/source/index.html

Sample output logs for iPerf client and server connections.

```text
Connecting to host 172.16.0.1, port 5201
[  5] local 172.16.0.2 port 52484 connected to 172.16.0.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   954 KBytes  7.81 Mbits/sec    0   79.2 KBytes
[  5]   1.00-2.00   sec  1.12 MBytes  9.44 Mbits/sec    0    126 KBytes
[  5]   2.00-3.00   sec  1.00 MBytes  8.39 Mbits/sec   12   49.5 KBytes
[  5]   3.00-4.00   sec   640 KBytes  5.24 Mbits/sec    2   42.4 KBytes
[  5]   4.00-5.00   sec   512 KBytes  4.19 Mbits/sec    2   39.6 KBytes
[  5]   5.00-6.00   sec   512 KBytes  4.19 Mbits/sec    2   33.9 KBytes
```

```text
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 172.16.0.2, port 52482
[  5] local 172.16.0.1 port 5201 connected to 172.16.0.2 port 52484
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec   634 KBytes  5.19 Mbits/sec
[  5]   1.00-2.00   sec   950 KBytes  7.78 Mbits/sec
[  5]   2.00-3.00   sec   977 KBytes  8.00 Mbits/sec
[  5]   3.00-4.00   sec   533 KBytes  4.36 Mbits/sec
[  5]   4.00-5.00   sec   553 KBytes  4.53 Mbits/sec
[  5]   5.00-6.00   sec   537 KBytes  4.40 Mbits/sec
```

--------------------------------

### Run srsUE

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/embms/source/index.rst.txt

Command to start the UE and receive eMBMS data.

```bash
sudo ./srsue ~/.config/srsran_4g/ue.conf
```

--------------------------------

### Network Execution Commands

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_sa_amari/source/index.rst.txt

Commands to start the 5GC, gNB, and UE components.

```bash
sudo ltemme mme.cfg
```

```bash
sudo lteenb gnb-nsa.cfg
```

```bash
sudo srsue ue.conf
```

--------------------------------

### Expected srsUE Terminal Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/embms/source/index.rst.txt

Example log output indicating successful eMBMS service start.

```text
Searching cell in DL EARFCN=3400, f_dl=2685.0 MHz, f_ul=2565.0 MHz
Found Cell:  Mode=FDD, PCI=1, PRB=50, Ports=1, CFO=-0.0 KHz
Found PLMN:  Id=00101, TAC=7
Random Access Transmission: seq=20, ra-rnti=0x2
Random Access Complete.     c-rnti=0x46, ta=1
RRC Connected
MBMS service started. Service id:0, port: 4321
Network attach successful. IP: 172.16.0.2
Software Radio Systems LTE (srsRAN  4G)
```

--------------------------------

### eNodeB Startup Console Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/handover/source/index.rst.txt

Example output showing the initialization of the eNodeB with ZMQ RF device configuration.

```text
Reading configuration file /etc/srsran_4g/enb.conf...

Built in Release mode using commit 7e60d8aae on branch next.

Opening 2 channels in RF device=zmq with args=fail_on_disconnect=true,id=enb,tx_port0=tcp://*:2101,tx_port1=tcp://*:2201,rx_port0=tcp://localhost:2100,rx_port1=tcp://localhost:2200,id=enb,base_srate=23.04e6
CHx base_srate=23.04e6
CHx id=enb
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
CH0 rx_port=tcp://localhost:2100
CH0 tx_port=tcp://*:2101
CH0 fail_on_disconnect=true
CH1 rx_port=tcp://localhost:2200
CH1 tx_port=tcp://*:2201
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Setting frequency: DL=2630.0 Mhz, UL=2510.0 MHz for cc_idx=0
Setting frequency: DL=2630.0 Mhz, UL=2510.0 MHz for cc_idx=1

==== eNodeB started ===
Type <t> to view trace
```

--------------------------------

### PHY-layer Log Example

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/2_ue_getstarted.rst.txt

Example of a detailed PHY-layer log message.

```text
17:52:26.094 [PHY1]  Info  [05788]  PDSCH:    l_crb= 1, harq=0, snr=22.1 dB, CW0: tbs=55, mcs=22, rv=0, crc=OK, it=1, dec_time=  12 us
```

--------------------------------

### Install Configuration Files

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsepc/source/2_epc_getstarted.rst.txt

Run this script to copy default configuration files to the user's local configuration directory.

```bash
srsran_4g_install_configs.sh user
```

--------------------------------

### Standard Log Example

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/2_ue_getstarted.rst.txt

Example of a standard RLC layer log message.

```text
17:52:25.246 [RLC ]  Info    DRB1 Tx SDU
```

--------------------------------

### Install srsRAN 4G Dependencies

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/handover/source/index.rst.txt

Command to install required system dependencies on Ubuntu systems.

```bash
sudo apt-get install cmake libfftw3-dev libmbedtls-dev libboost-program-options-dev libconfig++-dev libsctp-dev
```

--------------------------------

### UE Startup Command and Console Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/handover/source/index.rst.txt

Command to initiate the UE and the expected console output during initialization.

```bash
sudo srsue
```

```text
Reading configuration file /etc/srsran_4g/ue.conf...

Built in Release mode using commit 7e60d8aae on branch next.

Opening 1 channels in RF device=zmq with args=tx_port=tcp://*:2001,rx_port=tcp://localhost:2000,id=ue,base_srate=23.04e6
CHx base_srate=23.04e6
CHx id=ue
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
CH0 rx_port=tcp://localhost:2000
CH0 tx_port=tcp://*:2001
Waiting PHY to initialize ... done!
Attaching UE...
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
```

--------------------------------

### Instantiate UE with Network Namespace

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/handover/source/index.html

Sets up the UE with ZMQ and creates a network namespace for isolation.

```bash
#!/bin/bash

LOG_PARAMS="--log.all_level=debug"

PORT_ARGS="tx_port=tcp://*:2001,rx_port=tcp://localhost:2000"
ZMQ_ARGS="--rf.device_name=zmq --rf.device_args=\"${PORT_ARGS},id=ue,base_srate=23.04e6\" --gw.netns=ue1"


## Create netns for UE
ip netns list | grep "ue1" > /dev/null
if [ $? -eq 1 ]; then
  echo creating netspace ue1...
  sudo ip netns add ue1
  if [ $? -ne 0 ]; then
   echo failed to create netns ue1
   exit 1
  fi
fi

sudo srsue ue.conf ${LOG_PARAMS} ${ZMQ_ARGS} --rat.eutra.dl_earfcn=3350 "$@"
```

--------------------------------

### Install PCSC dependencies on Debian/Ubuntu

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/4_ue_advanced.rst.txt

Install the necessary development headers and daemon for PCSC support.

```bash
sudo apt-get install libpcsclite-dev pcscd pcsc-tools
```

--------------------------------

### Install Build Dependencies

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/pi4/source/index.rst.txt

Install cmake and system updates required for building srsRAN 4G.

```bash
sudo apt update
sudo apt upgrade
sudo apt install cmake
```

--------------------------------

### Start eNB/gNB

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_nsa_zmq/source/index.rst.txt

Command to launch the eNB and expected output confirming ZMQ channel configuration.

```bash
sudo srsenb
```

```text
Opening 2 channels in RF device=zmq with args=fail_on_disconnect=true,tx_port0=tcp://*:2000,rx_port0=tcp://localhost:2001,tx_port1=tcp://*:2100,rx_port1=tcp://localhost:2101,id=enb,base_srate=23.04e6
CHx base_srate=23.04e6
CHx id=enb
Current sample rate is 1.92 MHz with a base rate of 23.04 MHz (x12 decimation)
CH0 rx_port=tcp://localhost:2001
CH0 tx_port=tcp://*:2000
CH0 fail_on_disconnect=true
CH1 rx_port=tcp://localhost:2101
CH1 tx_port=tcp://*:2100

==== eNodeB started ===
Type <t> to view trace
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Current sample rate is 11.52 MHz with a base rate of 23.04 MHz (x2 decimation)
Setting frequency: DL=2680.0 Mhz, UL=2560.0 MHz for cc_idx=0 nof_prb=50
Setting frequency: DL=1842.5 Mhz, UL=1747.5 MHz for cc_idx=1 nof_prb=52
```

--------------------------------

### Build and Install srsRAN 4G

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/pi4/source/index.html

Compile srsRAN 4G from source and install default configuration files.

```bash
sudo apt install libfftw3-dev libmbedtls-dev libboost-program-options-dev libconfig++-dev libsctp-dev
git clone https://github.com/srsRAN/srsRAN_4G.git
cd srsRAN_4G
git checkout tags/release_19_12
mkdir build && cd build
cmake ../
make -j4
sudo make install
sudo ldconfig

## copy configs to /root
sudo ./srsran_4g_install_configs.sh user

```

--------------------------------

### Network Element Startup Scripts

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/handover/source/index.rst.txt

Bash scripts for launching eNB 1, eNB 2, and the UE with ZMQ RF device configuration and network namespace setup.

```bash
#!/bin/bash

LOG_ARGS="--log.all_level=debug"

PORT_ARGS="tx_port=tcp://*:2101,rx_port=tcp://localhost:2100"
ZMQ_ARGS="--rf.device_name=zmq --rf.device_args=\"${PORT_ARGS},id=enb,base_srate=23.04e6\""

OTHER_ARGS="--enb_files.rr_config=rr1.conf"

sudo srsenb enb.conf ${LOG_ARGS} ${ZMQ_ARGS} ${OTHER_ARGS} $@
```

```bash
#!/bin/bash

LOG_ARGS="--log.all_level=info"

PORT_ARGS="tx_port=tcp://*:2201,rx_port=tcp://localhost:2200"
ZMQ_ARGS="--rf.device_name=zmq --rf.device_args=\"${PORT_ARGS},id=enb,base_srate=23.04e6\""

OTHER_ARGS="--enb_files.rr_config=rr2.conf --enb.enb_id=0x19C --enb.gtp_bind_addr=127.0.1.2 --enb.s1c_bind_addr=127.0.1.2"

sudo srsenb enb.conf ${LOG_ARGS} ${ZMQ_ARGS} ${OTHER_ARGS} $@
```

```bash
#!/bin/bash

LOG_PARAMS="--log.all_level=debug"

PORT_ARGS="tx_port=tcp://*:2001,rx_port=tcp://localhost:2000"
ZMQ_ARGS="--rf.device_name=zmq --rf.device_args=\"${PORT_ARGS},id=ue,base_srate=23.04e6\" --gw.netns=ue1"


## Create netns for UE
ip netns list | grep "ue1" > /dev/null
if [ $? -eq 1 ]; then
  echo creating netspace ue1...
  sudo ip netns add ue1
  if [ $? -ne 0 ]; then
   echo failed to create netns ue1
   exit 1
  fi
fi

sudo srsue ue.conf ${LOG_PARAMS} ${ZMQ_ARGS} --rat.eutra.dl_earfcn=3350 "$@"
```

--------------------------------

### Hex Message Log Example

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/2_ue_getstarted.rst.txt

Example of an RLC layer log message with hex output enabled.

```text
17:52:25.246 [RLC ]  Info    DRB1 Tx SDU
             0000: 8b 45 00 00 c7 f3 8b 40 00 01 11 d1 f6 c0 a8 03
             0010: 01 ef ff ff fa 92 55 07 6c 00 b3 ee 41 4d 2d 53
```

--------------------------------

### Log Message Format Examples

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsenb/source/2_enb_getstarted.rst.txt

Examples of standard log output formats and hex message representations.

```text
Timestamp  [Layer ]  Level    Content
```

```text
17:52:25.246 [RLC ]  Info    DRB1 Tx SDU
```

```text
17:52:25.246 [RLC ]  Info    DRB1 Tx SDU
             0000: 8b 45 00 00 c7 f3 8b 40 00 01 11 d1 f6 c0 a8 03
             0010: 01 ef ff ff fa 92 55 07 6c 00 b3 ee 41 4d 2d 53
```

--------------------------------

### Install UHD Drivers

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/pi4/source/index.html

Install USRP Hardware Driver (UHD) packages and download necessary firmware images.

```bash
sudo apt install libuhd-dev libuhd3.15.0 uhd-host
sudo /usr/lib/uhd/utils/uhd_images_downloader.py

## Then test the connection by typing:
sudo uhd_usrp_probe

```

--------------------------------

### Run eNodeB

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/zeromq/source/index.rst.txt

Launch the eNodeB using ZMQ virtual radio configuration.

```bash
./srsenb/src/srsenb --rf.device_name=zmq --rf.device_args="fail_on_disconnect=true,tx_port=tcp://*:2000,rx_port=tcp://localhost:2001,id=enb,base_srate=23.04e6"
```

--------------------------------

### Install Build Dependencies

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/general/source/1_installation.rst.txt

Commands to install mandatory development libraries required for building srsRAN 4G from source.

```bash
sudo apt-get install build-essential cmake libfftw3-dev libmbedtls-dev libboost-program-options-dev libconfig++-dev libsctp-dev
```

```bash
dnf install cmake fftw3-devel mbedtls-devel lksctp-tools-devel libconfig-devel boost-devel
```

--------------------------------

### Example Network Attach Output

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/usermanuals/source/srsue/source/2_ue_getstarted.rst.txt

Sample console output showing a successful network attachment process.

```text
linux; GNU C++ version 6.3.0 20170618; Boost_106200; UHD_003.009.007-release
Reading configuration file /.config/srsran_4g/ue.conf...
Built in RelWithDebInfo mode using commit 6b2961fce on branch next.

Opening 1 RF devices with 2 RF channels...
Opening USRP with args: type=b200,master_clock_rate=30.72e6
Waiting PHY to initialize ... done!

Attaching UE...
Searching cell in DL EARFCN=2850, f_dl=2630.0 MHz, f_ul=2510.0 MHz
Found Cell:  Mode=FDD, PCI=1, PRB=6, Ports=2, CFO=1.3 KHz
Found PLMN:  Id=00101, TAC=7
Random Access Transmission: seq=42, ra-rnti=0x2
RRC Connected
Random Access Complete.     c-rnti=0x46, ta=0
Network attach successful. IP: 192.168.3.2
```

--------------------------------

### Run srsUE

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/5g_sa_E2E/source/index.rst.txt

Command to start srsUE from the build folder using a specific configuration file.

```bash
sudo ./srsue ue.conf
```

--------------------------------

### Install SCTP kernel module

Source: https://docs.srsran.com/projects/4g/en/latest/app_notes/source/pi4/source/index.html

Installs the missing SCTP kernel module required for srsRAN 4G on Ubuntu 22.04 LTS.

```bash
sudo apt-get install linux-modules-extra-raspi
```

--------------------------------

### Build srsRAN 4G

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/app_notes/source/pi4/source/index.rst.txt

Install required libraries, clone the srsRAN 4G repository, build the software, and install configuration files.

```bash
sudo apt install libfftw3-dev libmbedtls-dev libboost-program-options-dev libconfig++-dev libsctp-dev
git clone https://github.com/srsRAN/srsRAN_4G.git
cd srsRAN_4G
git checkout tags/release_19_12
mkdir build && cd build
cmake ../
make -j4
sudo make install
sudo ldconfig

## copy configs to /root
sudo ./srsran_4g_install_configs.sh user
```

--------------------------------

### Install srsRAN 4G via Ubuntu Packages

Source: https://docs.srsran.com/projects/4g/en/latest/_sources/general/source/1_installation.rst.txt

Use these commands to add the official repository and install the srsRAN 4G suite on Ubuntu systems.

```bash
sudo add-apt-repository ppa:softwareradiosystems/srsran
sudo apt-get update
sudo apt-get install srsran -y
```